Garage door broken? Call (425) 426-2728 — free estimates on repair and replacement in Renton.

Guide

Garage Door Opener Not Working? 6 Checks Before You Call

An opener that stops working is often not broken. Power, a lock button, a bumped sensor or a pulled release cord cause a large share of these calls. Here are six checks you can do safely, in order, and the signs that mean you should stop.

Updated November 18, 2026 · 6 min read

The short version

A garage door opener does one job: it moves a door that the springs have already balanced. So when the door will not move, the cause is in one of three places. The opener has no power or no signal, a safety feature is stopping it on purpose, or the door itself has become too heavy or is stuck.

The six checks below go from the simplest cause to the most serious one. None of them needs tools, and none of them asks you to touch springs, cables or the bottom brackets. If you reach check 6 and the door feels heavy, stop there. That is a spring problem, and running the opener against it damages the opener.

Check 1: Is the opener getting power?

Look at the motor unit on the ceiling. If no light comes on when you press the wall button and the unit is silent, start with power. Make sure the cord is fully in the ceiling outlet, then check the breaker panel. Many garage outlets are on a GFCI circuit, and a tripped GFCI outlet elsewhere in the garage will cut power to the opener. Press its reset button and try again.

If the wall button works but the remotes do not, power is fine. Go to checks 2 and 3.

Check 2: Is the wall control in lock mode?

Many wall controls have a lock or vacation button. When it is on, the wall button still works but every remote and keypad is ignored. It is easy to switch on by accident. A blinking light on the wall control is the usual sign. Check the manual for your model, and on most units you hold the lock button for a few seconds to turn it off.

Check 3: Remote and keypad

  • Replace the remote battery. A weak battery shows up first as a remote that only works when you are close to the door.
  • Try a second remote or the outdoor keypad. If one works and the other does not, the problem is that one device, not the opener.
  • If nothing wireless works but the wall button does, and lock mode is off, the remotes may need to be programmed again or the opener's receiver may have failed.

Check 4: Safety sensors (the door starts down, then goes back up)

Openers made for the US market since 1993 are required to have a reversing system, and on almost all of them that means two photo-eye sensors near the floor, one on each side of the door. If the beam between them is broken, the door will not close from the remote. The usual pattern is a door that starts down, stops, and returns to open while the opener light flashes.

  • Look for anything in the path of the beam: a box, a broom, a trash can, leaves.
  • Check the small light on each sensor. Both should be steady. A flickering or dark light usually means the sensors are out of line.
  • Wipe both lenses with a soft cloth.
  • If a sensor bracket was bumped, turn the sensor gently until its light is steady again.
  • Low sun shining straight into a sensor can cause the same symptom at certain times of day.

Check 5: Has the red release cord been pulled?

The red cord hanging from the opener rail disconnects the door from the opener so the door can be moved by hand. If it was pulled, the motor runs and the chain or belt moves, but the door stays where it is. Close the door fully by hand first. Then reconnect it the way your manual describes. On most openers you pull the cord toward the opener and run the opener once, and the carriage clicks back into place.

Do not pull the release cord while the door is open unless you are sure the springs are intact. If a spring is broken, a disconnected door can drop.

Check 6: Is it the door, not the opener?

With the door closed and disconnected from the opener, lift it by hand. A balanced door lifts with one hand and stays where you leave it at about waist height. If it feels very heavy, will not stay up, or will not lift at all, the opener is not the problem. A spring has broken or lost tension, or the door is binding in the tracks.

Look at the spring above the door without touching it. A visible gap in the coil means the spring is broken. Stop here. Do not keep pressing the button, and do not turn up the opener's force setting to make it pull harder. The force setting is a safety limit, and an opener that drags a door with a broken spring can strip its gear or burn out its motor.

Stop and call for a repair if you see any of these

Fix & Lift Garage Door repairs and installs garage door openers in Renton and nearby cities. Estimates are free, there is no service call charge, and the price is agreed before any work starts. Call (425) 426-2728.

  • The opener hums or grinds, the door is connected, and nothing moves.
  • The door is crooked in the opening, or a roller is out of the track.
  • A cable is loose, frayed or hanging.
  • You smell burning from the motor unit.
  • The door reverses every time and the sensors are clean, aligned and steady.
  • The door does not reverse when it meets an object on the floor.

Next step

If the door in question is misbehaving right now, describe what it is doing and we will tell you what it usually means and what the fix takes.

Questions we get asked about this

Why does my garage door opener hum but the door does not move?
There are three common causes. The release cord was pulled, so the opener is disconnected from the door. A spring is broken, so the door is too heavy for the opener to lift. Or a gear inside the opener has worn out. Close the door, disconnect it and lift it by hand. If it is heavy, the problem is the spring and not the opener.
Why does my garage door start to close and then go back up?
Most often the safety sensors near the floor are blocked, dirty or out of line, and the opener light flashes to tell you so. Clear the path, wipe the lenses and check that both sensor lights are steady. If the sensors are fine, the door may be meeting resistance on the way down and should be inspected.
Why did all my remotes stop working at once?
Check the lock or vacation button on the wall control first. When it is on, the wall button works and every remote and keypad is ignored. If lock mode is off and no remote works, the opener's receiver may need attention.
Should I turn up the force setting if the opener struggles to lift the door?
No. The force setting is a safety limit. A door that is hard to lift usually has a spring or track problem, and raising the force hides that problem while it wears out the opener and weakens the safety reverse.
Is it safe to use the red release cord?
Yes when the door is fully closed. When the door is open, pull it only if you are sure the springs are intact, because a door with a broken spring can drop once it is disconnected.
← All garage door guides

Free estimate

Tell us what your garage door is doing

Send a photo or describe the noise, the gap or the part that gave out. We will tell you what it usually means, what it takes to fix it and what it costs — before anyone touches the door.

  • Free estimate, no obligation to book.
  • The price you approve is the price you pay.
  • Parts for most residential doors ride on the van.
  • Renton-based — you reach the person doing the work.
(425) 426-2728

What is your door doing?

Free estimate. No obligation.

What is the problem?

By submitting you agree we may call or text you about this request. We do not sell your details.